| amp: | 1 | mix: | 1 | pre_mix: | 1 | pre_amp: | 1 |
| phase: | 0.25 | amp_min: | 0 | amp_max: | 1 | pulse_width: | 0.5 |
| phase_offset: | 0 | wave: | 1 | invert_wave: | 0 | probability: | 0 |
| prob_pos: | 0 | seed: | 0 | smooth: | 0 | smooth_up: | 0 |
| smooth_down: | 0 | pan_min: | -1 | pan_max: | 1 |
with_fx :panslicer
Slice the pan automatically from left to right. Behaves similarly to slicer and wobble FX but modifies stereo panning of sound in left and right speakers. Default slice wave form is square (hard slicing between left and right) however other wave forms can be set with the wave: opt.
Introduced in v2.6
| amp: |
The amplitude of the resulting effect.
Default: 1
|
| mix: |
The amount (percentage) of FX present in the resulting sound represented as a value between 0 and 1. For example, a mix of 0 means that only the original sound is heard, a mix of 1 means that only the FX is heard (typically the default) and a mix of 0.5 means that half the original and half of the FX is heard.
Default: 1
|
| pre_mix: |
The amount (percentage) of the original signal that is fed into the internal FX system as a value between 0 and 1. With a pre_mix: of 0 the FX is completely bypassed unlike a mix: of 0 where the internal FX is still being fed the original signal but the output of the FX is ignored. The difference between the two is subtle but important and is evident when the FX has a residual component such as echo or reverb. When switching mix: from 0 to 1, the residual component of the FX’s output from previous audio is present in the output signal. With pre_mix: there is no residual component of the previous audio in the output signal.
Default: 1
|
| pre_amp: |
Amplification applied to the input signal immediately before it is passed to the FX.
Default: 1
|
| phase: |
The phase duration (in beats) of the slices
Default: 0.25
|
| amp_min: |
Default: 0
|
| amp_max: |
Default: 1
|
| pulse_width: |
The width of the pulse wave as a value between 0 and 1. A width of 0.5 will produce a square wave. Different values will change the timbre of the sound. Only valid if wave is type pulse.
Default: 0.5
|
| phase_offset: |
Initial phase offset.
Default: 0
|
| wave: |
Control waveform used to modulate the amplitude. 0=saw, 1=pulse, 2=tri, 3=sine
Default: 1
|
| invert_wave: |
Invert control waveform (i.e. flip it on the y axis). 0=uninverted wave, 1=inverted wave.
Default: 0
|
| probability: |
Probability (as a value between 0 and 1) that a given slice will be replaced by the value of the prob_pos opt (which defaults to 0, i.e. silence)
Default: 0
|
| prob_pos: |
Position of the slicer that will be jumped to when the probability test passes as a value between 0 and 1
Default: 0
|
| seed: |
Seed value for rand num generator used for probability test
Default: 0
|
| smooth: |
Amount of time in seconds to transition from the current value to the next. Allows you to round off harsh edges in the slicer wave which may cause clicks.
Default: 0
|
| smooth_up: |
Amount of time in seconds to transition from the current value to the next only when the value is going up. This smoothing happens before the main smooth mechanism.
Default: 0
|
| smooth_down: |
Amount of time in seconds to transition from the current value to the next only when the value is going down. This smoothing happens before the main smooth mechanism.
Default: 0
|
| pan_min: |
Minimum pan value (-1 is the left speaker only)
Default: -1
|
| pan_max: |
Maximum pan value (+1 is the right speaker only)
Default: 1
|